Board specific definitions for the RE-Mote board Revision A. More...

Detailed Description

Board specific definitions for the RE-Mote board Revision A.

Author: Hauke Petersen hauke.nosp@m..pet.nosp@m.ersen.nosp@m.@fu-.nosp@m.berli.nosp@m.n.de; Antonio Lignan alina.nosp@m.n@zo.nosp@m.lerti.nosp@m.a.co.nosp@m.m; Sebastian Meiling s@mln.nosp@m.g.ne.nosp@m.t

Definition in file board.h.

#include "cpu.h"
#include "board_common.h"

Include dependency graph for board.h:

This graph shows which files directly or indirectly include this file:

Go to the source code of this file.

LED pin definitions
#define	LED0_PIN GPIO_PIN(3, 5)

#define	LED1_PIN GPIO_PIN(3, 4)

#define	LED2_PIN GPIO_PIN(3, 3)

#define	LED0_MASK (1 << 5)

#define	LED1_MASK (1 << 4)

#define	LED2_MASK (1 << 3)

#define	LED0_ON (GPIO_D->DATA \|= LED0_MASK)

#define	LED0_OFF (GPIO_D->DATA &= ~LED0_MASK)

#define	LED0_TOGGLE (GPIO_D->DATA ^= LED0_MASK)

#define	LED1_ON (GPIO_D->DATA \|= LED1_MASK)

#define	LED1_OFF (GPIO_D->DATA &= ~LED1_MASK)

#define	LED1_TOGGLE (GPIO_D->DATA ^= LED1_MASK)

#define	LED2_ON (GPIO_D->DATA \|= LED2_MASK)

#define	LED2_OFF (GPIO_D->DATA &= ~LED2_MASK)

#define	LED2_TOGGLE (GPIO_D->DATA ^= LED2_MASK)

User button pin definition
#define	BTN0_PIN GPIO_PIN(0, 3)

#define	BTN0_MODE GPIO_IN_PU

RF switch controlled by SW
Controls which RF interface goes to the RP-SMA external antenna These values configure the required pin to drive the RF antenna switch, to either enable the sub-1Ghz RF interface (power-up the CC1200) or the 2.4GHz RF interface of the CC2538, both alternatively routed to a RP-SMA connector to allow using an external antenna for both cases. Note it is also possible to enable both RF interfaces at the same time, by switching On the sub-1GHz RF interface, and placing an 0Ohm resistor (R19), to select between using a ceramic chip antenna (not mounted), or to connect and external antenna over a pigtail to the U.Fl connector (not mounted). RF switch state: LOW: 2.4GHz RF interface on RP-SMA connector, CC1200 powered-off. HIGH: Sub-1GHz RF interface on RP-SMA connector.
#define	RF_SWITCH_GPIO GPIO_PD2

#define	RF_SWITCH_SUB_GHZ gpio_set(RF_SWITCH_GPIO)

#define	RF_SWITCH_2_4_GHZ gpio_clear(RF_SWITCH_GPIO)

#define	RF_SWITCH_TOGGLE gpio_toggle(RF_SWITCH_GPIO)

Shutdown enable/done pins
#define	SHUTDOWN_DONE_GPIO GPIO_PD0

#define	SHUTDOWN_EN_GPIO GPIO_PD1

CC1200 SPI and pins definitions
#define	CC1200_SPI_DEV SSI0

#define	CC1200_MOSI_GPIO GPIO_PB1

#define	CC1200_MISO_GPIO GPIO_PB3

#define	CC1200_SCLK_GPIO GPIO_PB2

#define	CC1200_CSN_GPIO GPIO_PB5

#define	CC1200_RESET_GPIO GPIO_PC7

#define	CC1200_GPD0_GPIO GPIO_PB4

#define	CC1200_GPD2_GPIO GPIO_PB0

Macro Definition Documentation

◆ BTN0_MODE

#define BTN0_MODE GPIO_IN_PU

Definition at line 62 of file board.h.

◆ BTN0_PIN

#define BTN0_PIN GPIO_PIN(0, 3)

Definition at line 61 of file board.h.

◆ CC1200_CSN_GPIO

#define CC1200_CSN_GPIO GPIO_PB5

Definition at line 107 of file board.h.

◆ CC1200_GPD0_GPIO

#define CC1200_GPD0_GPIO GPIO_PB4

Definition at line 109 of file board.h.

◆ CC1200_GPD2_GPIO

#define CC1200_GPD2_GPIO GPIO_PB0

Definition at line 110 of file board.h.

◆ CC1200_MISO_GPIO

#define CC1200_MISO_GPIO GPIO_PB3

Definition at line 105 of file board.h.

◆ CC1200_MOSI_GPIO

#define CC1200_MOSI_GPIO GPIO_PB1

Definition at line 104 of file board.h.

◆ CC1200_RESET_GPIO

#define CC1200_RESET_GPIO GPIO_PC7

Definition at line 108 of file board.h.

◆ CC1200_SCLK_GPIO

#define CC1200_SCLK_GPIO GPIO_PB2

Definition at line 106 of file board.h.

◆ CC1200_SPI_DEV

#define CC1200_SPI_DEV SSI0

Definition at line 103 of file board.h.

◆ LED0_MASK

#define LED0_MASK (1 << 5)

Definition at line 40 of file board.h.

◆ LED0_OFF

#define LED0_OFF (GPIO_D->DATA &= ~LED0_MASK)

Definition at line 45 of file board.h.

◆ LED0_ON

#define LED0_ON (GPIO_D->DATA |= LED0_MASK)

Definition at line 44 of file board.h.

◆ LED0_PIN

#define LED0_PIN GPIO_PIN(3, 5)

Definition at line 36 of file board.h.

◆ LED0_TOGGLE

#define LED0_TOGGLE (GPIO_D->DATA ^= LED0_MASK)

Definition at line 46 of file board.h.

◆ LED1_MASK

#define LED1_MASK (1 << 4)

Definition at line 41 of file board.h.

◆ LED1_OFF

#define LED1_OFF (GPIO_D->DATA &= ~LED1_MASK)

Definition at line 49 of file board.h.

◆ LED1_ON

#define LED1_ON (GPIO_D->DATA |= LED1_MASK)

Definition at line 48 of file board.h.

◆ LED1_PIN

#define LED1_PIN GPIO_PIN(3, 4)

Definition at line 37 of file board.h.

◆ LED1_TOGGLE

#define LED1_TOGGLE (GPIO_D->DATA ^= LED1_MASK)

Definition at line 50 of file board.h.

◆ LED2_MASK

#define LED2_MASK (1 << 3)

Definition at line 42 of file board.h.

◆ LED2_OFF

#define LED2_OFF (GPIO_D->DATA &= ~LED2_MASK)

Definition at line 53 of file board.h.

◆ LED2_ON

#define LED2_ON (GPIO_D->DATA |= LED2_MASK)

Definition at line 52 of file board.h.

◆ LED2_PIN

#define LED2_PIN GPIO_PIN(3, 3)

Definition at line 38 of file board.h.

◆ LED2_TOGGLE

#define LED2_TOGGLE (GPIO_D->DATA ^= LED2_MASK)

Definition at line 54 of file board.h.

◆ RF_SWITCH_2_4_GHZ

#define RF_SWITCH_2_4_GHZ gpio_clear(RF_SWITCH_GPIO)

Definition at line 87 of file board.h.

◆ RF_SWITCH_GPIO

#define RF_SWITCH_GPIO GPIO_PD2

Definition at line 85 of file board.h.

◆ RF_SWITCH_SUB_GHZ

#define RF_SWITCH_SUB_GHZ gpio_set(RF_SWITCH_GPIO)

Definition at line 86 of file board.h.

◆ RF_SWITCH_TOGGLE

#define RF_SWITCH_TOGGLE gpio_toggle(RF_SWITCH_GPIO)

Definition at line 88 of file board.h.

◆ SHUTDOWN_DONE_GPIO

#define SHUTDOWN_DONE_GPIO GPIO_PD0

Definition at line 95 of file board.h.

◆ SHUTDOWN_EN_GPIO

#define SHUTDOWN_EN_GPIO GPIO_PD1

Definition at line 96 of file board.h.